Is It Easy to Install a Stereo

Download Article

A simple step-by-step guide to replacing your car stereo

Download Article

Installing a new car stereo can often be simple enough to do yourself, and his article will provide you with a general guide on how to do it. Keep in mind that some cars and systems are more complicated than others and that every car and stereo system will be different, so some specifics may vary. Be sure to read any instructions that come with the new car stereo before attempting to install it.

1. 1

   Set the parking brake and disconnect the negative cable from your car battery. Be sure to do this to avoid short-circuiting the electrical system during the installation, which could lead to fire or physical harm for you.^[1]

   • For instructions on disconnecting the battery, see How to Disconnect a Car Battery.

2. 2

   Unscrew any screws that are securing the trim in place. Be careful to remove all screws before trying to pry off the trim or you may break it.^[2]

   Advertisement

3. 3

   Remove the trim. For some cars, you may need to remove several pieces of plastic trim, usually working from the bottom up.^[3]

   • If you need to remove trim that includes any knobs or drawers, remove them before trying to pry off the trim.
   • Use your hands or a pry tool to pry off each piece of trim. Pry tools are specifically for this purpose and will not damage the trim pieces.

4. 4

   Pull out any necessary components. If you need to remove any components before being able to access the stereo, do so.

   • Disconnect components that are wired to the car. Take a picture of how each is wired for later reference.

5. 5

   Loosen the stereo. Different cars may have varying elements securing the stereo in place.

   • If the stereo is held in place by screws or nuts, loosen them with the appropriate tool (screwdriver or nutdriver, respectively).
   • If the stereo isn't held in place by screws or nuts, you'll need to use a radio-removal key. This tool is commonly necessary in Ford vehicles. Radio-removal keys (sometimes also referred to as radio-removal tools) will typically either be in an elongated horseshoe shape or will have a circular shape at one end and a notched shaft at the other. They're available at most auto-parts stores.
   • Insert the keys into the two small slots in the face of the stereo. You will release a mechanism holding the stereo in place. Slide the radio-removal keys into each slot again until you feel the stereo loosen from in its housing. You should then be able to pull out the stereo relatively easily.

6. 6

   Pull the stereo out of the panel. You may want to use needle-nose pliers to grip the edge of the stereo and help you pull it out.^[4] Pull it gently, and if the stereo doesn't come out easily, double check that you haven't missed any components that may be holding it in place.

7. 7

   Take a picture of how the stereo is wired. This is an important step because the photo will serve as a reference later when you're wiring in the new stereo.

8. 8

   Unplug the stereo connections. You'll see a series of wires connected to the back of the stereo, and you'll need to disconnect each of them.

   • First unplug the antenna wire, which will typically be a thicker wire plugged in separately from the rest. Once it's unplugged, you should be able to move the stereo around more freely.
   • Next unplug the each of the wire harness connectors. There will typically be several of these and you can recognize them because a series of wires will feed into each one. The plastic piece into which the wires are fed should have either a tab or a button you can push, which will release the harness.

Advertisement

1. 1

   Match up the wires. Match the wires of the car's harnesses to the new stereo's harnesses. Each harness connector is unique, so it should be easy to figure out which ones fit together.^[5]

   • To be safe, check the wiring diagrams for both your car and the new stereo to verify you've connected them correctly.
   • If your car's stereo doesn't use wire harnesses, you'll need to match up each wire manually. The wires are color-coded; however, the wires on an after-market stereo may not match with the color-coded wires in your vehicle. It's best to study and follow the wiring diagram that came with the stereo.
   • Connect the matched wires. There are two options for connecting the wires, crimping or soldering. Crimping is faster and easier, but soldering will provide a more stable and secure connection. Be sure to use the proper size crimper and don't try to bundle the wires with tape — it will eventually dry out and fall off. Bundle wires using zip ties instead.^[6]

2. 2

   Assemble the mounting kit. If your new stereo came with a separate mounting kit, assemble it according to the stereo's instructions (it will often mean fitting a metal housing sleeve into the mounting frame).

   • Push down on the tabs located around the metal sleeve with a screwdriver to secure the metal sleeve in place.

3. 3

   Connect the power source. Typically, if you have a wiring harness, this connection will be made when you connect the new stereo harnesses to the harnesses in the car.

   • If you aren't using a wiring harnesses, you'll need to manually connect the power. Determine whether your car has a switched power source (typically a red wire) or a constant power source (typically a yellow wire). Some vehicles even have both types of power sources. For more information on switched versus constant power, go here.

4. 4

   Ground the stereo. If you're using wiring harnesses, this connection will be made when you connect the harness pieces.

   • If you aren't using a wiring harness, you'll need to locate the bolt, wire, or screw that connects with the car's bare metal chassis. Loosen the bolt, wire, or screw and slip the stereo's ground wire (usually black) underneath, then tighten.
   • Note that the ground connection is important to the optimal performance of the stereo. If the ground wire doesn't connect to the bare metal, it won't work. And if the ground wire connection is loose, it could result in poor audio output. Sand down the area with sand paper to ensure a good connection.

5. 5

   Connect the remaining wires. Plug in the antenna cable and connect the stereo's wiring adapter to the the car's wire harness. Connect the output converter if one is needed to make the new stereo compatible with the car's audio system. Have in mind that all wires should be connected in the end and there should no single one hanging unattended.

6. 6

   Test the stereo. Turn the power on and test the AM, FM, and CD components. Test the fade and balance settings to be sure the speakers are working properly. Turn the power back off.

Advertisement

1. 1

   Push the stereo into place. When the stereo is fully in, you should hear it click into place.

2. 2

   Reconnect the components. Fasten in any screws that are needed to hold the stereo in place, reconnect any wired components, and replace any knobs or drawers that were removed.

3. 3

   Snap all the pieces of trim back into place over the stereo. Double check that all screws and trim pieces are securely in place.

4. 4

   Try out the new stereo. Turn the car power on again and play around with the stereo and its settings to be sure everything is in working order.

Advertisement

Add New Question

• Question

  How do I replace a 1996 Jeep radio with a Pioneer radio by matching the wires manually?

  

  It should be red to green, orange to purple, maroon to turquoise, pink to silver, and clear to black.

• Question

  How do I connect the stereo to the equalizer if the stereo has no input port?

  

  You have to buy an adapter cable. If you buy from a store like Radio Shack, you may be able to get the salesman to come outside and help you install it... For free!

• Question

  If I have an aftermarket Pioneer radio, and want to replace it with another Pioneer radio, do I need a new wiring harness?

  

  Not necessarily, just compare the harnesses and once they match, you can go ahead.

• Question

  Can the radio short out my battery?

  

  The radio can drain the battery, but should not short it out.

• Question

  Where can I connect an amp remote if a stereo does not have a remote on cable?

  

  Use the factory fuse box. Find a wire that turns on/off with the ignition key.

• Question

  What do I do if the stereo won't work after I disconnected it and put it back together?

  

  Check your connections. Make sure you have 12 volts to hot wire and a good ground. Some head units have a separate wire that must go to voltage for the display separately.

• Question

  What's the difference between an amp and a booster?

  

  Some people consider them the same. However, I would say that a booster is a 'go between' only to increase the power input to a subwoofer (or set of subwoofers), whereas an amplifier is to increase the power to all channels. Some amps also will provide an exclusive (or dedicated) output for a subwoofer or set of subwoofers in addition to the RF RR LF LR 4 channels.

• Question

  I have a second hand Peugeot 307 with a hole in the dashboard where a radio used to be. Is it a simple case of plugging in some connectors to a new radio unit?

  

  This will work only if you replace with a stereo with same connectors.

• Question

  Do I have to unhook the battery?

  

  No, but it doesn't hurt as a good safety precaution to prevent electric shock.

• Question

  Can I get an adapter for a car stereo if the connectors are different?

  

  Very often, yes. Retailer sites like Crutchfield and Amazon will show you what's needed to connect a radio you bought there to different makes and models of car. They're usually not strictly necessary but can simplify the installation.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

• Be sure to purchase a stereo that will fit your car's make and model. If you need help deciding what to buy, go to an electronics store or a store specializing in auto electronics and ask for assistance choosing a stereo. If a stereo does not fit there are may be an aftermarket kits available to make it fit. For more information, go here.

• Some retailers may offer to install your stereo for free or minimal cost if you buy it from them, so be sure to inquire.

• When removing any screws or nuts, place them in the car's cup holder so they don't get lost.

Advertisement

• Follow the specific instructions provided with the new stereo. Some of the installation steps may be specific to your car and stereo.

• If you find yourself feeling lost or frustrated, get help from a professional — otherwise you may damage the car or hurt yourself.

Advertisement

Things You'll Need

• A car with a stereo system
• A new stereo
• Phillips and flat head screwdrivers (depending on model)
• Nutdriver (depending on model)
• Radio-removal keys (depending on model)
• Pry tool (optional)
• Needle nose pliers (optional)
• Zip ties
• Electrical tape
• Soldering gun or crimp connectors

About This Article

Article Summary X

To install a car stereo, match the wires of the car's harnesses to the new stereo's harnesses. Each harness connector is unique, so it should be easy to figure out which ones fit together, but you can check the wiring diagrams for your car and your new stereo if you're not sure. If your car's stereo doesn't use wire harnesses, you'll need to match up each wire individually. Assemble the mounting kit if your stereo came with one, then slide the stereo into place and fasten any screws that are needed to hold the stereo in place. Keep reading to learn how to take out your original stereo!

Did this summary help you?

Thanks to all authors for creating a page that has been read 1,079,319 times.

Is this article up to date?

richardseliablive.blogspot.com

Source: https://www.wikihow.com/Install-a-Car-Stereo

Share this post